Seals: transfer case input-output, pinion.

Original and compatible parts

Postby jwgreen » Wed Feb 26, 2014 9:56 pm

RiverPatrol wrote:Justin, you're even awesomer! :D :clap: :dance: :lol:

Thanks Leslie, I'm just tying to impart what little knowledge I have to this site. :D
Justin
jwgreen Offline

User avatar
I love driving my Patrol!
I love driving my Patrol!
 
Posts: 650
Images: 70
Joined: Thu Oct 24, 2013 11:23 am
Location: Iola, Tx
Has thanked: 43 times
Been thanked: 259 times
Location: Iola, Tx

Postby RMP&O » Thu Apr 30, 2015 12:20 pm

This seal is still available from Nissan. Couple winters ago I walked into Napa here in my tiny little town with the seal in hand. They called their Nissan dealership they get parts from, didn't mention truck it was for but read the number off the seal. Two weeks later I had a set of seals from Nissan. Recently I have bought more of them, directly from Nissan.

Cheers
RMP&O Offline

User avatar
You know you own a Patrol when…
You know you own a Patrol when…
 
Posts: 415
Images: 80
Joined: Tue Apr 14, 2015 12:12 am
Has thanked: 181 times
Been thanked: 171 times
Location: Wyoming

Postby RiverPatrol » Thu Apr 30, 2015 12:23 pm

What part number did you order?
Beyond any hope for intervention

Image
RiverPatrol Offline

User avatar
Administrator
Administrator
 
Posts: 5659
Images: 718
Joined: Thu Oct 04, 2012 10:42 am
Has thanked: 3453 times
Been thanked: 1136 times
Location: Temecula, CA

Postby RMP&O » Thu Apr 30, 2015 6:19 pm

RiverPatrol wrote:What part number did you order?


38189-44000

http://www.amayama.com/search?region=315&q=38189-44000

Cheers
RMP&O Offline

User avatar
You know you own a Patrol when…
You know you own a Patrol when…
 
Posts: 415
Images: 80
Joined: Tue Apr 14, 2015 12:12 am
Has thanked: 181 times
Been thanked: 171 times
Location: Wyoming

Postby Esteban » Thu Apr 27, 2017 5:05 pm

I ordered the following seal from eBay just to have in stock:

AVX Shaft Oil Seal TC50x73x12 Rubber Lip 50mm/73mm/12mm metric (use this for the search)

http://www.ebay.com/itm/AVX-Shaft-Oil-S ... 5d60384466

It's not double lipped as the original (to keep oil in, and water out). It does have an outer lip that will keep dust out. Will work if you're not fording any streams.
Owner of the same Patrol since 1967
Esteban Offline

User avatar
Helping others revive their Patrol…
Helping others revive their Patrol…
 
Posts: 2045
Joined: Sat Feb 23, 2013 11:28 am
Location: Ashburn, Virginia
Has thanked: 2397 times
Been thanked: 794 times
Location: Ashburn, VA

Postby rdarnell » Fri May 26, 2017 9:49 am

just purchased SKF 17758 and 18979 from Rockauto... not sure when I will get around to using them though...
rdarnell Offline

User avatar
You know you own a Patrol when…
You know you own a Patrol when…
 
Posts: 288
Images: 132
Joined: Mon Feb 27, 2017 9:05 am
Has thanked: 97 times
Been thanked: 120 times
Location: Louisville KY USA

Postby rdarnell » Fri May 26, 2017 9:51 am

rdarnell Offline

User avatar
You know you own a Patrol when…
You know you own a Patrol when…
 
Posts: 288
Images: 132
Joined: Mon Feb 27, 2017 9:05 am
Has thanked: 97 times
Been thanked: 120 times
Location: Louisville KY USA

Postby Esteban » Fri May 26, 2017 10:43 am

rdarnell wrote:just purchased SKF 17758 and 18979 from Rockauto... not sure when I will get around to using them though...


I'm getting these measurements for them:

SKF 17758 (for Transfer input seal)
Width (in) 0.354--->9.0 mm
Shaft (in) 1.772--->45.0 mm
Bore (in) 2.677--->68.0 mm

SKF 18979
Width (in) 0.276--->7.0 mm
Shaft (in) 1.89--->48.0 mm
Bore (in) 2.874--->73.0 mm

If you're planning to use SKF 18979 for the Transfer case output seals, and the pinion seals, the inside dia. (Shaft) might be too tight. The shaft is 50 mm. I measured it before ordering the ones from eBay. Member 2869ral did report that the inner dia. was a bit tight, and he found the ones on eBay after that.
Owner of the same Patrol since 1967
Esteban Offline

User avatar
Helping others revive their Patrol…
Helping others revive their Patrol…
 
Posts: 2045
Joined: Sat Feb 23, 2013 11:28 am
Location: Ashburn, Virginia
Has thanked: 2397 times
Been thanked: 794 times
Location: Ashburn, VA

Postby Shad » Fri Jun 29, 2018 4:04 pm

Does anyone have an extra output shaft seal to sell.... 38189-4400?
I am out of commission until I locate one.
Thanks
Shad
425-250-8093
Shad Offline


Patrol Newbie
Patrol Newbie
 
Posts: 6
Joined: Mon May 21, 2018 2:54 pm
Has thanked: 0 time
Been thanked: 0 time
Location: SF Bay Area

Postby rdarnell » Mon Mar 25, 2019 2:18 pm

looks like the time to put all the seals I have acquired is getting close. I have ordered new bearing too!6246
rdarnell Offline

User avatar
You know you own a Patrol when…
You know you own a Patrol when…
 
Posts: 288
Images: 132
Joined: Mon Feb 27, 2017 9:05 am
Has thanked: 97 times
Been thanked: 120 times
Location: Louisville KY USA

Postby rdarnell » Sun Apr 07, 2019 8:37 pm

Just order pinion seals from the above amayama site. The AVX 50x73x12 seals feel a little too tight for my liking.
rdarnell Offline

User avatar
You know you own a Patrol when…
You know you own a Patrol when…
 
Posts: 288
Images: 132
Joined: Mon Feb 27, 2017 9:05 am
Has thanked: 97 times
Been thanked: 120 times
Location: Louisville KY USA

Previous

Return to Parts and Compatible Parts

Who is online

Users browsing this forum: No registered users and 1 guest