Page 2 of 2

Re: Seals: transfer case input-output, pinion.

PostPosted: Wed Feb 26, 2014 9:56 pm
by jwgreen
RiverPatrol wrote:Justin, you're even awesomer! :D :clap: :dance: :lol:

Thanks Leslie, I'm just tying to impart what little knowledge I have to this site. :D

Re: Seals: transfer case input-output, pinion.

PostPosted: Thu Apr 30, 2015 12:20 pm
by RMP&O
This seal is still available from Nissan. Couple winters ago I walked into Napa here in my tiny little town with the seal in hand. They called their Nissan dealership they get parts from, didn't mention truck it was for but read the number off the seal. Two weeks later I had a set of seals from Nissan. Recently I have bought more of them, directly from Nissan.

Cheers

Re: Seals: transfer case input-output, pinion.

PostPosted: Thu Apr 30, 2015 12:23 pm
by RiverPatrol
What part number did you order?

Re: Seals: transfer case input-output, pinion.

PostPosted: Thu Apr 30, 2015 6:19 pm
by RMP&O
RiverPatrol wrote:What part number did you order?


38189-44000

http://www.amayama.com/search?region=315&q=38189-44000

Cheers

Re: Seals: transfer case input-output, pinion.

PostPosted: Thu Apr 27, 2017 5:05 pm
by Esteban
I ordered the following seal from eBay just to have in stock:

AVX Shaft Oil Seal TC50x73x12 Rubber Lip 50mm/73mm/12mm metric (use this for the search)

http://www.ebay.com/itm/AVX-Shaft-Oil-S ... 5d60384466

It's not double lipped as the original (to keep oil in, and water out). It does have an outer lip that will keep dust out. Will work if you're not fording any streams.

Re: Seals: transfer case input-output, pinion.

PostPosted: Fri May 26, 2017 9:49 am
by rdarnell
just purchased SKF 17758 and 18979 from Rockauto... not sure when I will get around to using them though...

Re: Seals: transfer case input-output, pinion.

PostPosted: Fri May 26, 2017 9:51 am
by rdarnell

Re: Seals: transfer case input-output, pinion.

PostPosted: Fri May 26, 2017 10:43 am
by Esteban
rdarnell wrote:just purchased SKF 17758 and 18979 from Rockauto... not sure when I will get around to using them though...


I'm getting these measurements for them:

SKF 17758 (for Transfer input seal)
Width (in) 0.354--->9.0 mm
Shaft (in) 1.772--->45.0 mm
Bore (in) 2.677--->68.0 mm

SKF 18979
Width (in) 0.276--->7.0 mm
Shaft (in) 1.89--->48.0 mm
Bore (in) 2.874--->73.0 mm

If you're planning to use SKF 18979 for the Transfer case output seals, and the pinion seals, the inside dia. (Shaft) might be too tight. The shaft is 50 mm. I measured it before ordering the ones from eBay. Member 2869ral did report that the inner dia. was a bit tight, and he found the ones on eBay after that.

Re: Seals: transfer case input-output, pinion.

PostPosted: Fri Jun 29, 2018 4:04 pm
by Shad
Does anyone have an extra output shaft seal to sell.... 38189-4400?
I am out of commission until I locate one.
Thanks
Shad
425-250-8093

Re: Seals: transfer case input-output, pinion.

PostPosted: Mon Mar 25, 2019 2:18 pm
by rdarnell
looks like the time to put all the seals I have acquired is getting close. I have ordered new bearing too!6246

Re: Seals: transfer case input-output, pinion.

PostPosted: Sun Apr 07, 2019 8:37 pm
by rdarnell
Just order pinion seals from the above amayama site. The AVX 50x73x12 seals feel a little too tight for my liking.