Re: Fabricated side steps
Posted: Fri Dec 12, 2014 8:24 am
snazzy... 
60Patrol
An open forum for all enthusiasts of the classic 60 series Nissan Datsun Patrol to gather and share information and gain knowledge. Members share off-road stories, restoration advice, modification ideas in an atmosphere free of a single controller. The fo
https://60patrol.com/forum/
Fabricated side steps
Page 8 of 10
Re: Fabricated side steps
Posted: Fri Dec 12, 2014 12:20 pm
Ron does amazing work.
Re: Fabricated side steps
Posted: Fri Dec 12, 2014 12:21 pm
In his little Arizona Patrol Fabrication Facility... A.k.a. the APFF.RiverPatrol wrote:Ron does amazing work.
Re: Fabricated side steps
Posted: Tue Jun 02, 2015 7:09 pm
I am makeing 3 sets of side steps, 2 sets will be available for sale if anyone is interested. I will have them done in a couple of days $125.00 + shipping. Please let me know. I will give it a day or two and then post them on ebay. 
Re: Fabricated side steps
Posted: Tue Jun 02, 2015 10:09 pm
Put me down for one of those sets Ron, and just ship them with the vent unless you have already sent it.2869ral wrote:I am makeing 3 sets of side steps, 2 sets will be available for sale if anyone is interested. I will have them done in a couple of days $125.00 + shipping. Please let me know. I will give it a day or two and then post them on ebay.
Re: Fabricated side steps
Posted: Tue Jun 02, 2015 10:23 pm
Ok you got it Justin. Thanks
Re: Fabricated side steps
Posted: Tue Jun 02, 2015 10:33 pm
Her are Kardok0s' (Suhails') side steps. Any one else need any? I have 1 set left.
Re: Fabricated side steps
Posted: Wed Jun 03, 2015 7:04 am
I would love to have a set to replace the tube / pipe that the PO put on mine, but I'd have to track down some brackets as well. Do you happen to have (or have made) any brackets?2869ral wrote:Any one else need any? I have 1 set left.
Re: Fabricated side steps
Posted: Wed Jun 03, 2015 8:12 am
Yes i make the brackets too. You can see them in this thread a page or two back. Steps and arms are $275.00+shipping, and they look very close to original. Let me know. I might be able to get these done by Fri. If not i will be out of town on vacation until the 14th.ckhorne wrote:I would love to have a set to replace the tube / pipe that the PO put on mine, but I'd have to track down some brackets as well. Do you happen to have (or have made) any brackets?2869ral wrote:Any one else need any? I have 1 set left.
Re: Fabricated side steps
Posted: Thu Jun 04, 2015 1:10 am
Another really nicely made piece!! Well done!
I took side step to the same place in Idaho I had the rear step fab'ed up at. Here are some pictures....
painted and mounted
It must be a bit tricky to make the mounting brackets. They are very specific since they don't mount on a flat part of the frame. I restored the ones above, they were pretty good originals. There is a flaw in the design though, they are hollow with no drain hole. I put some drain holes in the mounting brackets.
Cheers
I took side step to the same place in Idaho I had the rear step fab'ed up at. Here are some pictures....
painted and mounted
It must be a bit tricky to make the mounting brackets. They are very specific since they don't mount on a flat part of the frame. I restored the ones above, they were pretty good originals. There is a flaw in the design though, they are hollow with no drain hole. I put some drain holes in the mounting brackets.
Cheers